VERYPRO-290, Universal Programmer for 15000 devices, with ZIF40 Socket and USB VeryPro-299 is a low-cost universal programmer. It supports over 19.000 different components as EPROMS until 32 pins (2764 to 27C801), parallel EEPROMS (2804 to 28C040), serial EEPROMS (24xx / 25xx / 35xx / 58xx / 59xx / 60xx / 64xx / 85xx / 93xx / 95xx...), FLASH memories in 32 pins (28Fxxx / 29Fxxx / 37xxx / 39xxx / 49xxx), populars microcontrollers (87Cxx / 89Cxx / AT90Sxx / PIC12Cxx / PIC16Cxx / PIC12Fxx / PIC16Fxxx) and PLDs (ATF16Vxx / ATF20Vxx / ATF22Vxx / GAL16Vxx / GAL20Vxx / GAL22Vxx). It has an IC test software to identify logic components (C-mos4000 / 74xxx / LM324 / LM339 / ULN20xx / ULN28xx) and it can test Static RAM / Dynamic DRAM. Il can accept low voltage components until 1,8V and has an autodetection for poors pins contacts. With severals components it can work without wall transformer on USB port. The software works with Windows 98/ME/2000/XP/VISTA/Windows7/Windows8/Windows10 (32bits and 64 bits). Accepts standard file formats: JEDEC, INTEL (Extended) HEX, HOLTEK, EMC(.CDS), INTEL HEX16, Motorola S record, BINARY, Tektronix (linear & segmented), and auto find format. Manages 16 and 32 bit word split (Set Programming). Features Test Vector capability and multiarray fuse map editor. Test TTL/CMOS logic ICs and Dynamic/Static Random Access Memory devices. Optimum programming for each individual device. Automaticly identifies the manufacturer and type of E(E)PROMs, auto identifies TTL/CMOS logic IC. Device insertion test and poor pin contact check. Modify algorithm parameters. Set addresses intelligently, such as device start address, device end address, from buffer address and so on. Support down to 1,8V low voltage devices. Not need exterior adapter for mostly devices. Universal DIP, PLCC, QFP, TSOP, PSOP, SOIC, SSOP, SDIP adapters. Auto-run mode starts programming automatically upon detection of chip insertion. Auto system test. Mass production mode. Supports Windows XP / VISTA / Windows 7 / Windows8 / Windows10 (32bit and 64bit) with 100MB of spare capacity. Hardware & Electrical specifications Dimensions product: 115 x 79 x 18mm. Weight : 130g Dimensions package: 185 x 130 x 50mm. Poids: 400g. Power supply : adapter with AC input 100V to 240V, 50Hz/60Hz, output 9Vdc/0,6A. Interface : connect to laptop or PC throught USB port (USB 1.1). Support : ZIF40 pin-drivers, (support 8 pins to 40 pins DIP package)

ZCM64M, Smartcard EEPROM (Microchip, 24LC64), 8KBytes Serial I²C bus EEPROM smartcardManufacturer: Microchip with part number reference: 24LC64Memory size : 64Kbits (80192 Bytes of 8-bits)Blank Smartcard without any software to create a prototypeI²C standard 2-wires serial interface programming onlyRead / Write mode: see datasheet of Microchip 24LC64 for detailsPower supply: 1.8V to 5.5VErase / Write cycles: 1,000,000 times minimumData retention: 200 years minimumMaximum Frequency: 400KHzTemperature: -40°C to +85°CDimensions: 85 x 53 x 1 mmWeight: 10g

Seeit PRESTO Programmer The Seeit PRESTO is a universal SPI programmer which enables quick and easy programming of a range of different microcontrollers (MCUs). The PRESTO module is compatible with Microchip PIC MCUs, AVR ATMEL MCUs and serial EEPROMs. A full list of compatible MCU devices can be found on the datasheet. The Seeit PRESTO connects to your PC via USB and connects directly to the MCU device with the attached 7 wires. The PRESTO module connects to devices soldered on the PCB with special packages, without having to add any adapters. You do not require an external power supply either as the PRESTO is powered via your PC. The “GO” button on the front of the PRESTO allows you to start programming quickly. The LEDs on the programmer indicate status, so you don’t require a PC, keyboard or mouse, if you wish. • High speed programming• Compatible with tonnes of MCUs• “GO” button for quick programming• Supports ICSP (In-Circuit Serial Programming) and ISP (In-System Programming) What’s included?ProgrammerSPI cableUSB cableSoftware (CD)User Manual (English and French)Operating System Requirements:Windows 98SE/ME/2000/XP/Vista/7/8/10LinuxOptional Adapters:These optional adapters can be used to extend the voltage range.HPR3V3 (772-3072)HPR1V2 (772-3081)HPRAVR (772-3084)ISP2ZIF (772-3088)

SEEIT PIC-02 Microcontrollers Programmer The SEEIT programmer PIC-02 will program microcontrollers such as PIC16C54 and PIC16C5x that are not supported by PIC-01. The connection is made via a parallel lead (supplied) Sub D25M - Sub D25F to the parallel port of your PC and operates with the PP5X software under DOS or Windows 95/98/ME (32bits). Tulip sockets for 18 pin and 28 pin DIP packagesSupports: PIC16C54, PIC16C56amd PIC16C58Supported by PP5X: PIC16C54, PIC16C55, PIC16C56 and PIC16C57Supplied withParallel extension cableCD-ROM SoftwareInstruction manual: French and English

TM-91 Radiation Meter, SEEIT The TM-91N radiation monitor is the survey meter in measuring the Gamma, Beta, X-Ray radiation with Geiger-Mueller tube. It is useful in monitoring the environment home safety, nuclear, medical, mining and metal industries. It is also ideal for the border control, customs and goods inspections. Measurements are displayed on a LCD monitor with low and alarm settings. The measurement can be displayed in μSiever/h or μRem/h with a range of 0,5 μS/h to 1400 μS/h or 50μRem/h to 140000 μRem/h. It is an excellent device, high sensitivity, for living environments or industrial environments. Measurement : Gamma, Beta, X-Ray. Units : MicroSiever/h (μS/h) or MicroRem/h (μRem/h). Range : 0,5μS/h to 1400μS/h or 50μRem/h to 140000μRem/h. Accuracy : 20% with resolution of 0,01μS/h or 1μRem/h, (Cesium 137).Energy dependency : 30KeV to 1,3 Mev. Display : 3-1/2 digits with LCD display. Simple rate : 10 seconds (20μS/h). Alarm setting : 0,50μS/h to 20 μS/h, (adjustable). Low battery indication. Auto power off : 0 to 60 mn, (adjustable). 0 disable auto power of. Battery life : approximate 50 hours. Operation temperature : +5°C to +40°C. Humidity: 0% to 80% RH. Storage temperature : -10°C to +50°C. Humidity: 0% to 70% RH. Hardware & Electrical specifications Dimensions device : 143 x 74 x 34mm. Weight : 175g. Dimensions package : 200 x 120 x 67mm. Weight : 350g. With 1 alkaline battery 9V type 6F22 (include).

ADA-TSOP28-12, Universal Adapter TSOP28 to DIP28 The TSOP28 to DIP28 universal adapter connect the pins of an 8/16/18/20/28-pin TSOP device (width=12mm) to a 28-pin DIP equivalentIt accepts a TSOP28-12 device and plug into a DIP socketEquivalent adapters from other manufacturers: WL-TSOP28-T, PA28TS28D-EO, SA430T

ZCM16M, Smartcard EEPROM (Microchip, 24LC16B), 2KBytes Serial I²C bus EEPROM SmartcardManufacturer: Microchip with part number reference: 24LC16BMemory size: 16Kbits (2048 Bytes of 8-bits)Blank Smartcard without any software to create a prototypeI²C standard 2-wires serial interface programming onlyRead / Write mode: see datasheet of Microchip 24LC16B for detailsPower supply: 2.5V to 5.5VErase / Write cycles: 1,000,000 times minimumData retention: 10 years minimumMaximum Frequency: 400KHzTemperature: -55°C to +125°CDimensions: 85 x 53 x 1 mmWeight: 10g

ADA-PLCC28, Universal Adapter PLCC28 to DIP28 The PLCC28 to DIP28 universal adapter connect the pins of a 28-pin PLCC device to a 28-pin DIP equivalentIt accepts a PLCC device and plug into a DIP socketThe pin 1 of the component is mark by hollow dot. Insert the component with this hollow dot on the top sideEquivalent adapters from other manufacturers: WL-PL28-U1, PA28PL28D, SA008A

ADA-SO20-200, Universal Adapter SOP8/SOP16/SOP20 to DIP20 The SOP20 to DIP20 universal adapter connect the pins of an 8/16/18/20-pin SOP device to a 20-pin DIP equivalentWidth: 200mil or 210milIt accepts a SOP device and plug into a DIP socketEquivalent adapters from other manufacturers: WL-SOP20-U1, PA20SO20D-EO-210, SA605A / SA605B

Seeit DIP Socket Adapters A range of universal adaptors from Seeit designed to convert to DIP packages. ADA-SOIC16-150: SOP8/14/16 to DIP16 (454-6803)ADA-QFN28: MLF28/QFN28 to DIP28 (919-5536)ADA-SSOP28: SSOP8/14/16/28 to DIP28 (919-5520)ADA-SO28-300: SOP18/28 to DIP28 (509-6292)ADA-PLCC32-32: PLCC32 to DIP28 / DIP32 (454-6819)ADA-PLCC32: PLCC32 to DIP32 (919-5539)ADA-TQFP32: TQFP32 to DIP32 (919-5532)ADA-TSOP32-14: TSOP32 to DIP32 (509-6309)ADA-TSOP32-20: TSOP32 to DIP32 (454-6831)ADA-QFN44: MLF44/QFN44 to DIP44 (919-5545)ADA-PLCC44: PLCC44 to DIP44 (454-6825)ADA-TSOP48-20: TSOP32/40/48 to DIP48 (454-6847)

Seeit DIP Socket Adapters A range of universal adaptors from Seeit designed to convert to DIP packages. ADA-SOIC16-150: SOP8/14/16 to DIP16 (454-6803)ADA-QFN28: MLF28/QFN28 to DIP28 (919-5536)ADA-SSOP28: SSOP8/14/16/28 to DIP28 (919-5520)ADA-SO28-300: SOP18/28 to DIP28 (509-6292)ADA-PLCC32-32: PLCC32 to DIP28 / DIP32 (454-6819)ADA-PLCC32: PLCC32 to DIP32 (919-5539)ADA-TQFP32: TQFP32 to DIP32 (919-5532)ADA-TSOP32-14: TSOP32 to DIP32 (509-6309)ADA-TSOP32-20: TSOP32 to DIP32 (454-6831)ADA-QFN44: MLF44/QFN44 to DIP44 (919-5545)ADA-PLCC44: PLCC44 to DIP44 (454-6825)ADA-TSOP48-20: TSOP32/40/48 to DIP48 (454-6847)

FLASHBIOS, Low-Cost Universal Programmer for EPROM/EEPROM/Flash, with USB The FlashBios is a device Reader/Programmer/Copier supporting CMOS EPROMs (2716 to 27C801 family) of 16Kb to 8Mb, parallel EEPROMs (28C16 to 28C040 family) up to 4Mb, parallel FLASH memory (28xxx, 29xxx, 37xxx, 39xxx, 49xxx, etc) of 512Kb to 8Mb, I²C and SPI EEPROMs memory (24Cxx, 25Cxx) and SPI FLASH memory (25Fxxxx) until 256Mb. It is equipped with a LED indicating the different status of the programmer, a USB port, a high quality tulip socket supporting devices in DIP packages of 8, 24, 28 or 32 pins and a PLCC32 socket supporting any 32-pin FLASH memory. The FlashBios connects to the USB port of any compatible PC and does not require any external power supply which makes it very practical to use at the office or on a business trip. Its integrated supply runs all the devices requiring a supply of 2.5V / 3.3V / 5.0V / 12V / 12.5V / 13V / 21V and 25V. New 32-pin devices can be added to the software list on request and the updates can be downloaded freely from our website. The software works with Windows 98/ME/2000/XP/Vista/Windows7 (32-bit and 64-bit). Accepts standard file formats: BINARY, INTEL (Extended) HEX, INTEL HEX16, Motorola S19/S28/S37 recordsRead / Write / Blank-Check Write / Verify / Blank-Check / Erase functionsSupport low voltage devices from 2.5V to 5.0VSupport high Vpp programming voltage: 12V / 12.5V / 13V / 21V / 25VNo need of exterior adapter for all DIP package devices : DIP8, DIP24, DIP28 and DIP32PLCC32 adapter on board to program parallel FLASH memorySPI connectors to program on board devices, (Gnd, Vdd, Vpp, DATA0, DATA1, DATA2, DATA3, DATA4, DATA5, DATA7)Supports Windows 98 / ME / 2000 / XP / Vista / Windows 7 (32-bit and 64-bit) with 10MB of spare capacityDimensions board: 140 x 100 x 15 mm Kit Contents Programmer with tulip DIP8 and DIP32 package, PLCC32 and SPI connectorUSB cableSoftware on CD-ROM